Sprayer/Spreader
Clamp, Boom 1" Triumph (Qty:1)
(fits all Triumph models) The 1" Boom Clamp helps hold the Spray Shield to the front bumper bar of the Triumph. Four (4) boom clamps are needed per spray shield. Spray Shield kits including this part is T000317-SprayShield Kit.
Spinner Kit, w/ Shaft
(fits all Triumph models) This is a upgrade for Serial #10501-12656. Standard for all other Triumph models.
Gearbox, Heat Shield Triumph 6" (all Triumph models)
(All Triumph models) Used to keep debris and water from entered gearbox top bearing.
Label, Spread Rate Adjustment
(fits 2015- present Triumph Sulky Hubs) This label is used on machine ranging from 2015 to present. Label identifies the rate the machine can be adjusted to spread granular fertilizer.
Triumph Hopper Cable Assembly
(fits all Triumph models) This is the hopper cable for the Triumph. It connects with fertilizer lever on the handlebars and the slide plate located underneath the hopper. This cable will help open and close the spreader hopper
Fitting, Elbow 1/4fptX1/4hb Triumph
Elbow fitting connected to nozzle bodies of high gear wide, high gear trim, and low gear trim nozzles. Three (3) of these fittings on machine.
Nozzle, WIDE Green HG-2016
(fits Triumph models Serial #14797-present)
PermaGreen® Agitator - Universal Upgrade Kit w/ Cam
(All Triumph Models) The PermaGreen® Agitator Upgrade Kit can be used on older model Magnum and Triumphs. Also, fits Lesco push spreaders. This kit will include the PermaGreen® Agitator as well as the Cam & Shaft for the Agitator, along with a wrench to tighten the set screw needed to tighten the Agitator on the Shaft. This kit includes the following part: 1 qty T422400-Permagreen Agitator Kit-The PermaGreen® Agitator Upgrade Kit can be used on older model Magnum and Triumphs. Also, fits Lesco push spreaders 1 qty T100103-PermaGreen Agitator Cam Similar kits to consider are: T000685-Agitator Shaft + PermaGreen Kit T000690-Agitator Block & Shaft Kit T000695-Agitator Upgrade KIT Complete
Nozzle Cap Gasket
(all Triumph models) (all Magnum models) The Nozzle Cap Gasket is used on all PermaGreen® models. This item is located inside the nozzle cap that holds the nozzles on the nozzle body. The Nozzle Cap Gasket will help prevent liquid for leaking out of the nozzle caps.
Pulley, Pump Triumph
(fits all Triumph models) Pump Pulley for the Triumph is located on the shaft of the pump and will come with two set screws.
Fitting, Elbow 1/4fptX3/8hb Triumph
Elbow fitting connected to nozzle body for the low gear broadcast nozzle on the Triumph. Only one per machine
Stainless Steel Spray Shield Upgrade Kit (Triumph)
(all Triumph models) Spray Shield Upgrade kit can be used on both Triumph. Shield kit is used to minimize spray liquid from spraying on hood. This Upgrade is replacing T000315-SprayShield Upgrade Kit. Old kit had plastic shield. This kit has an updated stainless steel shield. This upgrade kit includes the following part number: 2 qty P651660-1/4-20 x 5/8 Screw 2 qty R651216-Lock Nut, 1/4-20 4 qty T454250-Boom Clamp 1" 2 qty T454255-1/4 Mnbt Fitting 2 qty T454260-1/4 Nylon Nut 1 qty T622103-Sprayshield