Lever, Throttle
(fits all Triumph models) Located on top right handlebar on the Triumph. This lever will pulley back on the throttle cable that is connected to the engine.
Handlebar Grip (Triumph)
Replace your old worn out grips to ensure proper control of the machine.
Spinner Gearbox Hood Bearing (Triumph)
This bearing goes over the shaft coming up from the Triumph Spinner Gearbox that comes up through hole in the middle of the green plastic hood piece.
Sulky, Foot Pads
(fits all Triumph models) **FOOT PADS ARE NOW ORANGE/BLACK** Foot pads are located on the sulky. Self stick foot pads ensure operator safety while on the machine. Anti-fatigue mat provides comfort for operator feet while operating machine.
Knob, Fert Rate Kit
(all Triumph models) This knob upgrade kit had a new and improved know that can be locked in place by a nylon locknut. This kit includes the following parts: 1 qty T422937 New, Knob Fert Rate 1 qty T645945 1/4-20 Zinc Locknut 1 qty T645940 1/4-20x1-1/4 Zinc Carriage Bolt Instructions for this kit, give illustrations of how to install new knob.
Lever, Brake/Spray Triumph
(all Triumph models) Brake/Spray Lever is the plastic black levers used on both front and rear brakes, along with the spray lever located on both sides of handlebars. Old part is #T654140.
Shaker Striker
(Triumph models Serial #14151-present) Used on block set T651969 to strike plate on hood.
Upgrade Foot Pad Kit
(fits all Triumph models) NEW Thicker pads Foot pads are located on the sulky. Self stick foot pads ensure operator safety while on the machine. Anti-fatigue mat provides comfort for operator feet while operating machine. Kit includes instructions and flat blade to remove old Foot Pads.
Triumph Hood (fits Triumph models Serial #10501-14150)
(fits Triumph models Serial #10501-14150) Hood NO LONGER attaches with hardware.
Nut, Square Nylon
(fits all Triumph models) This part is used for attaching body panels to machines in various places.
Hood w/ Striker Plate (2015 or Newer Triumphs)
(fits Triumph models Serial #14151-present) HOOD NO LONGER ATTACHES WITH HARDWARE Hood piece for Triumphs 2015 and newer. Located underneath the impeller and covers the inner workings of the machine, such as the pump, spinner gearbox, and transaxle. Also includes a striker plate that helps the hood shake during use. (Use block #T651969)
Clip, Push on Retaining 1/2 Triumph
(fits all Triumph models) This push on retainer is located on the left hand side of the bottom of the fertilizer lever. It helps hold the fertilizer lever and deflector lever securely onto the handlebar housing.
Screw, 1" w/Sealing Washer
Screws w/Sealing Washer is used to fasten down the green hood pieces
Everlasting Spring Keeper Kit
Reduces the risk of Idler Spring coming off and separating from machine. Kit contains the following: (1) P650117 #8-32 Locknut (1) T650880 #8 Spacer (1) T101582 Idler Spring Adjuster (1) R651450 Washer 3/16 X 3/4 (1) T654545 Idler Spring Assembly
Rod End, Hardened Female
(all Triumph models) This part is located between the sulky and frame. On triumph this part is attached to a male rod end (T652663) is a part of the articulation of the sulky. This part is a hardened rod end. Replaces old part #R652462.
Stud, B
(fits Triumph models Serial #12657-16999) Stud is used on sulky to attach female rod end on sulky.
Hour Meter
(fits all Triumph models) Monitors hours on machine as well as engine rpm's.
Hood, Striker Bracket
(fits Triumph models Serial #14151-present) This bracket is on the hood of the Triumph.
Lever, Fertilizer
(all Triumph models) Fertilizer Levers are located in between the handlebars and is used to open and close the hopper holes to engage or disengage the spread of granule out of the hopper. Does not include rubber grips. (Parts # T654310 &#T654325)
Joint, Assembly Top Articulating Triumph
(all Triumph models)
Hopper Grip
(fits all Triumph models) LEFT SIDE GRIP USED ON FERT LEVER
SmartSteer™ Handlebar Spring (Triumph)
This parts are used on Triumph Handlebars. This part replaces dampeners on original Triumph machines. Kit is available. Call PermaGreen® for more details. Part number for for kit is T000475-2017 Smartsteer Upgrade Kit
Rod End, Hardened Male
(all Triumph models) This part is located between the sulky and frame. On triumph this part is attached to a female rod end (T652662) is a part of the articulation of the sulky. This rod end is a hardened rod end. Part replaces old part #R652672.
Snubber Ring
fits Triumph serial #10501-14150 Snubber Rings are black rubber snubbers located where the handlebars meet the differential housing and cushion the movement of the handlebars
2015-Hood Shaker Kit
Hood Shaker fits all Triumph Machines. This upgrade kit helps to vibrate fertilizer off of the hood. Spreading most of the fertilizer instead of collecting on the hood. Block has a finger that strikes a metal plate, which vibrates hood continuously. Hood Shakers were first assembled on machines in 2015.(Starting with C1C-2015 Triumph) If you have A1A and B1B Triumphs build between 2010 to 2014 buy this upgrade kit today. This was not a standard kit during those years. If you need to replace existing parts, this kit should have everything you need to replace worn parts.
Pump/Gearbox Bracket
(fits all Triumph models)
Plain Grip
RIGHT HAND GRIP USED ON FERT LEVER
Shift Lever
(fits all Triumph models)
Rate Adjustment Assembly
(fits Triumph models 2015-present includes serial #14151-present) The Rate Adjustment Assembly is located underneath the hopper, next to the shut-off plate. This assembly has a knob that when tightened lock the location of the shut-off plate to allow the operate to clear out the holes and return to the original spread opening. This assembly includes the following items: 1 qty T422937-Knob Fert Rate 2 qty R651550-Nylon Washer 0.32 ID, 0.56 OD 1 qty T645270-1/4-20x3/8 Socket Head screw ss 1 qty T645275-1/4-20x1-1/2 Carriage Bolt ss 1 qty T645280-1/4-20x5/8 Round Head Screw ss 3 qty R651216-Lock Nut, 1/4-20 1 qty R651480-Lock Washer, 1/4 1 qty R651420-Stainless Washer, 1/4 1 qty T645970-#10 x 1/2 Pan Screw 1 qty T651600-1/2 Nylon Spacer 1 qty T101538-Fert Stop Lever
2015-Handlebar Assembly
(fits Triumph serial # 14151 - Present)
Frame/Body