Sprayer/Spreader
Spinner Platter (Triumph all models) (Magnum models that have been updated)
The Dual-Sided Impeller/Platter is used to spread the granule material as it is being dropped from the bottom of the hopper. This item is used on the Triumph models and can be used on Magnum models that have been converted with Magnum Spinner Kit.
Spinner Belt (Triumph)
(all Triumph models) Spinner Belt for the Triumph. Goes around the spinner gearbox pulley, pump pulley, and gearbox pulley.
Spray Cable (Triumph)
(all Triumph models) This is the spray cable for the Triumph. It connects to the spray lever on the left handlebar and the main spray valve located under the top green panel.
Pump Assembly
(fits all Triumph models) This pump is used on all Triumphs. Assembly comes with the following parts: 1 qty Pump 2 qty R651206-10x24 lock nut 1 qty R651450-3/16 Fender washer The following parts could be order along with this part: P442065-Elbow Fitting (This is the elbow that is the connecting part to the pump in plumbing assemblies) P442059-Blue Retaining Clip (This part is the clip that pushes holds the elbow fitting onto the pump. Locks Elbow in place.)
Hopper Cover (All Triumph models)
(fits all Triumph models) Hopper Cover goes over the hopper of all Triumph models. This cover helps to keep granular material in the hopper while in operation.
PermaGreen® Agitator Kit
This universal agitator fits all PermaGreen® machines and Lesco push spreaders. The patented PermaGreen® Agitator Kit is great for preventing clogging in the hopper holes while spreading fertilizer, seed, rock salt, or any other product used in the Triumph. Also, provides a consistent, full spread for better accuracy and results.
Spray Valve Kit Triumph
(fits all Triumph models) This kit is used on all triumphs. Kit includes the following parts: 1) P205010-Spray Valve 2) R452222-Fitting, 1/4 mpt x 3/8 Hose 3) T454245-3/8 mpt x 3/8 hose barb 4) R347042-Wire Tire, Stud 5) R347041-Wire Tire 8 BUV (2) 6) R4841243-Hose Clamp #38 (2) 7) P205020-Spring 3" (not shown in picture) This kit is used to replace spray valve. Kit includes hose fittings, wire tires and hose clamps to completely change out spray valve.
Diaphragm, Standard (Magnum and Triumph all models)
(all Triumph models) (all Magnum models) The diaphragm is used on all PermaGreen® models. The diaphragm is a rubber disk located underneath the 8 psi cap on the nozzle body and the 20 psi and 30 psi pressure caps on the unloader valves. There are five total on every PermaGreen®. Always a good practice to have a few extra on hand.
Deflector Cable (Triumph all models)
The deflector cable controls the deflector used on border passes for all Triumph models.
Triumph 3" Spring (Spray Valve, Deflector, Throttle)
(fits all Magnum models) (fits all Triumph models) 3" Spray Valve Spring is used to help close the main spray valve on the Triumph. Also used on deflector. All Triumph models use this spring for Throttle spring. Magnum models used this spring to pull the main spray valve.
Spinner Gearbox w/ Pulley (Triumph)
(fits all Triumph models) This is the gearbox that is used on all Triumphs. This part engages the spinner shaft and impeller to spread granular product. This gearbox kit comes with the parts show below: 1 qty gearbox 1 qty T653710-3"OD 1/2 bore w/2 set screws 4 qty R651206-Lock Nut 1/4-20 1 qty T210165-Gearbox Heat Shield 6" 4 qty P650105-Set Screw 1/4-20 x 1 ss
3rd Hole Cable w/ Plastic Lever Triumph
(all Triumph models) This controls 3rd hole slide plate on all Triumph models and includes plastic lever, black plastic cable/lever housing, gray rate adjuster and cable. Metal lever version is available as part number T654056